MW70E4: Bộ chuyển đổi framed E1 sang 4 cổng Ethernet

Liên hệ

MW70E4 là bộ chuyển đổi framed E1 sang 04 cổng ethernet của hãng UPCOM. Thiết bị cung cấp đường truyền vật lý giữa  giao diện chuẩn framed E1 ITU-T G.703 (E1) và giao diện 10/100Base-T. Bộ chuyển đổi giao diện E1-4ETH sử dụng công nghệ FPGA, được thiết kế nhỏ gọn và giá thành hợp lý. Hiện thiết bị được sử dụng rộng rãi trong việc kết nối giữa mạng WAN và LAN, trong các bài toán giám sát,.....

Tính năng sản phẩm
1.   Based on self -copyright IC 
2.   E1 supports any timeslot set, the rate is 64K-2048K
3.   Can realize monitor and control of remote equipment,OAM management data did not take up user’s timeslot and save E1 bandwidth
4.   Have the function of E1 interface loop back check,avoid the converter crashed because of interface loop return;
5.   Have indicator when the device is power-off or E1 line is broken or lose signal;
6.   Can set the E1 line that not to send the LINK signal to Ethernet interface while E1 line is broken;
7.   The Ethernet interface supports jumbo frames (1916 Bytes);
8.   4Channel 10M/100M Ethernet interface can isolate each other to realize communication independently;
9.   Ethernet interface supports 10M/100M, half/full duplex auto-Negotiation and AUTO-MDIX (crossed line and straightly connected line self-adaptable );
10.  Provide 2 clock types: E1 master clock and E1 line clock;
11.  Have three Loop Back Mode: E1 interface Loop Back (ANA)、Ethernet interface Loop Back(DIG)、Command the remote Ethernet interface Loop Back(REM)
12.  Have pseudo random code test function, easy the installation and maintenance;
13.  Provide 2 impedances: 75 Ohm unbalance and 120 Ohm balance;
14.  Have Ethernet monitor self-reset function, the equipment will not dead
15.  Ethernet interface supports the counters of receiving and transmitting frame, receives wrong frame counters.  
16.  E1 interface supports the counters of receiving wrong frame;
17.  Realize monitor of remote equipment temperature and voltage from local equipment;
18.  Support SNMP Network Management;
19.  Can form the structure: Ethernet E1 Bridge(A)---E1 Optical Fiber Modem(B)---Ethernet Optical Fiber Modem (C)

Thông số kỹ thuật:

E1 Interface

 

Interface Standard

comply with protocol G.703

Interface Rate

n*64Kbps±50ppm

Interface Code

HDB3

E1 Impedance

75Ω (unbalance), 120Ω (balance)

Jitter tolerance

In accord with protocol G.742 and G.823

Allowed Attenuation

0~6dBm

Ethernet interface (10/100M)

 

Interface rate

10/100 Mbps,  half/full duplex auto-negotiation

Standard

Compatible with IEEE 802.3, IEEE 802.1Q (VLAN)

MAC Address Capability

4096

Connector

RJ45, support Auto-MDIX

Power

 

Power supply

AC180V ~ 260V;DC–48V;DC +24V

Power consumption

≤10W

Dimension

 

Product Size

216*140*31mm(W*D*H)

Simple packaging

274*193*84mm(W*D*H)

Piece Weight

1.2KG

Working environment

 

Working temperature:

-10°C ~ 50°C

Storage temperature

-40℃~80℃

Humidity

5%~95% (no  condensation)

Warranty

3years

Nội dung tùy chỉnh viết ở đây
popup

Số lượng:

Tổng tiền: